Custom Homebuilder Houston Heights | Installing shower wall tile correctly
Written for Bicycle Bugalows
Tile showers done by Bicycle Bungalows, Custom Homebuilder Houston Heights should not only be leak proof, they should look good. On any project, We’ve protected against leaks by substituting dens shield for drywall, and using a liquid membrane to waterproof the floors, all seams at corners and benches, and all fasteners. The next step is to set the porcelain wall tile in a running bond or brick pattern so that it looks good and stays put.
1. Layer in the layout. Custom Homebuilder Houston Heights always plans the layout to make sure the tile is centered and symmetrical. The goal is to maximize the size of tiles at the bottom and top, avoiding narrow pieces. I avoid using a four piece at the top because the ceiling is usually not perfectly level. By cutting the top course of tile on all three walls I can keep the joint with consistent all the way around. In this case, I also had to consider two niches. Twins sure they would be symmetrical, I sized in located them in advance so that the picture frame trim tile at the top and bottom with Paul on the horizontal joints between four wall tiles. This results in nearly equal 6 inch white courses at the ceiling and shower pan.
2. Butter the tile, don’t lather the wall. In showers and wet areas, I always use latex modified thin set mortar, not mastic. When exposed to water, mastic simply turns to liquid, which can cause the tiles to crack and eventually fall off the wall. Rather than spread thin set on the wall I preferred to better than sad onto the back of every tile with a 1/4 inch notched trowel. This keeps the work area neat and clean, and reduces the amount of water that works into the joints, which makes routing easier.
3. Skip the spacers. Custom Homebuilder Houston Heights begins on the long wall, applying tile from the centerline outward toward the corners. I start with the first four course, which I sat on a temporary ledger that I’ve leveled and fastened around all three walls. After all the wall tile mortar has cured, I will remove the ledger, set the tile on the floor and skip the spacers. I began on the long wall, applying tile from the centerline outward toward the corners. I start with the first floor course, which I set on a temporary ledger that I’ve leveled and fasten around all three walls. After all the wall tile mortar has cured, I will remove the ledger, set the Floor tile, then fill in the course of tiles at the shower pan. I’m spacing three styles 3/16 inch apart. But I don’t like to use spacers. Spacing the tiles by I is faster and, after many years of setting tile, I’m pretty good at it. More important, with some tile, that it mentions very, so using SPG servers will lead to crooked joint‘s in the grout. The 3/16 inch grout joint allow for some irregularity in the edges of the porcelain tile. The tile that has more uniform, I can use one 8 inch or even 1/16 inch joints.
4. With the first course set except for the cut pieces at the corners, Custom Homebuilder Houston Heights uses a 4 foot level to check that the tile is flat and in plane. This is especially important with larger tiles in a running bond pattern because irregularities in tile thickness or boulders or depressions in the wall can skew the corners and create a left at the joints. I adjust as needed by tapping the tile or resetting a tile after adding w with the first course set except for the cut pieces at the corners, or use a 4 foot level to check that the tile is flat and in playing. This is especially important with larger tiles in the running bond pattern because irregularities in tile thickness or bulges or depressions in the wall can’t skew the corners and create a left at the joints. I adjust as needed by tapping the tile we’re resetting a tile after adding mortar.
5. Check the level. Even though the first row of tile is laid on a level ledger screwed to the wall, I double checked with a level. This first row of tiles is critical because if these tiles are crooked, the whole world will end up cricket. This is also one place where shims come in handy. Are you shims as needed to bring the tops of the tiles perfectly snag with the level.
6. Measure twice, cut once. Both ends of the first chorus need Cut pieces. Because shower walls are frequently out of plum, I always measure cards at both the bottom and the top. With 3/16 inch grout lines, I will cut the tile 1/4 inch shorter than the measurement. I am going to have cuts in every course that I like to install as much tile as I can before making a trip to the song. I wait until I have dimensions for several courses, then cut them all at once.
7. Custom Homebuilder Houston Heights will Check the level at every course. To make the running bond or brick pattern, the second course is offset by a half tiles with. I measure from both sides to the center line. To make sure this tile is properly aligned because it sets the pattern for all of the courses above. Again, I level across the second row to keep the horizontal joints consistent. As with the first course, our use spacers were needed to bring the tile into alignment.
8. Dry tiles after cutting. If cut tiles are wet from the saw, the thin set will not bond as well. I always wipe them with a rag to remove any moisture. After setting the cut pieces, custom homebuilder Houston Heights will use a level again to check alignment.
9. Work outside in on sidewalks. When setting the side wall tiles, start at the outside edge and work toward the corner. Ideally, the outside edge of the side walls will start only with full and half tiles. As with the back wall, play as much detail as you can before making a trip to the saw for cats.
10. Plan the corner cuts. The goal when planning layout of the sidewalls is to a void Nero slivers of tile on both sides of the corner. With larger tiles like the ones I’m using here, I try to make it look as if the tile folds or bands around the corner. So, where the lawn cut tile on the back wall dies into a corner a short piece of tile should come out of the corner on the side wall.